Cleaning Tips
1. UPHOLSTERY
a. Light SoilingWipe down soiled upholstery with a mild solution of 10% household liquid dish soap and 90% warm water – applied with a soft damp cloth.For areas requiring something a bit stronger, use a solution of liquid cleanser and warm water applied with a soft bristle brush.
Wipe away any residual cleaning solution with a water dampened cloth.
b. Difficult Stains
Dampen a soft cloth with a solution of 10% household bleach (sodium hypochlorite) and 90% water. Rub gently. When finished, rinse with a water dampened cloth to remove any residual bleach concentrate.
c. Luster
To restore some of the lost sheen and luster to your upholstery apply a light coat of spray furniture wax to the upholstery surface, and buff lightly using a clean cloth.
CAUTION: When using strong cleaning agents such as bleach or rubbing alcohol, first test them in an inconspicuous area to insure they do not damage the fabric or alter the color.
PrimaFit, its directors, officers, agents and staff cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning products.
2. FRAMES
Rust, Scratches and Gouges
Perspiration is corrosive and will get into any tiny openings in even the best paint finishes.
Keeping the equipment clean and dry will help prevent rust and corrosion. Users should be instructed to wipe any liquid spills immediately and use a cloth to wipe the equipment dry after each workout, to remove remaining perspiration.
Equipment should be cleaned at least once a week (more for high use facilities).
Wipe down with a clean, damp cloth containing a mild cleaning agent such as a water and dish-soap solution and then dry to clean perspiration and dirt off the frame and surfaces.
Avoid abrasive cleaners - as these could scratch or damage the equipment finish.
Scratches and gouges will occur from time to time. Addressing them while they are small will help prevent them from spreading, causing larger problems, and will greatly increase the longevity of your strength equipment and keep it looking in top shape!
To minimize fine scratches, use a mild automotive polish, applied and removed with a soft, clean cloth to help fill in minor scratches. Applied to the metal frame, this wax also acts as an additional protective layer against moisture, guarding against rust.
Do not place the equipment in an area of high humidity, such as near a steam room, sauna, indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine can adversely affect the finish of the product.
3. CHROME TUBES (Not Guide Rods)
Clean chrome tubes using chrome polish-then help keep your chrome protected by adding an additional protective layer with car wax seal.Neutral cleaners (pH between 5.5 and 8.5) are recommended, and dry thoroughly and avoid acid or chlorine based or abrasive cleaners that can scratch or damage the equipment.
4. HARDWARE
Inspect all nuts and bolts for looseness, tighten as required.
5. GRIPS
Inspect grips for wear or damage and replace as necessary.
Inspect all handles and bars for wear or damage, particularly at any tab style connecting points, and replace as necessary.
Inspect all snap links for proper latching or wear, and replace as necessary.
6. WEIGHT STACKS COMPONENTS AND GUIDE RODS
Inspect all weight stacks and increment weight systems for proper alignment and smoothness of operation.
Wipe all guide rods clean over their entire length, and then lubricate with a light coat of medium weight automotive engine oil.
A DRY silicon spray may be used. Do not use Teflon spray as a guide rod lubricant. Never use WD-40 as a guide rod lubricant as it is primarily a cleaner and degreaser.
7. BELTS AND CABLES
Inspect all belts and cables for proper tension and any non-uniformity, wear or damage along their entire length. Run your fingers on the cable or belt, paying particular attention to bends in the cable or belt and attachment points.
Things to look for that would indicate a need to replace a cable or belt:
- any tears or cracks in the cables outer sheath that would expose the wire cable
- one or more kinks in the cable
- a curled cable outer sheath
- necking,a distinct narrowing or stretching of the cable sheath
- peeling of the belt,s skin
- waves or distortions in the belt
- narrowing of any portion of the belt in excess of 1/32 inch than the rest of the belt
- any crack or splits
- fraying of the belt or Kevlar strands hanging outReplace worn or damaged cables IMMEDIATELY!
B. Rust Prevention Tips :
1. If possible, maintain a consistent temperature and humidity level at all times.
2. If possible, ensure that HVAC systems prevent pool and spa air (as well as unconditioned coastal air) from exchanging into the workout area. Pool and spa air contain chlorine, acid and mineral salts – all of which are highly corrosive agents.
3. Enforce exerciser post-workout wipe down of equipment with a soft towel to remove sweat.
4. Clean equipment daily with a soft cotton cloth and a mild cleaner, such as a dish soap and water solution, to remove corrosives and efectively clean the surfaces. Apply the cleaner to the cloth, not directly to the equipment surfaces. Do not use paper towels.
5. If highly caustic floor cleaning products are used around the equipment, utilize the minimum concentration of the cleaning solution.
6. Inspect for scratched surfaces and be sure to clean, treat and touch up paint to prevent corrosion from spreading.
7. Overall, it is a good idea to use a protective coating, such as automotive wax or spray furniture polish containing wax, in locations where detrimental environmental factors cannot be minimized. They will provide a layer of protection between your equipment and the environment, as well as keep your equipment looking great. When using these products, test a small area of the machine to ensure there is no discoloration before applying to larger surfaces.
|
